|
![]() |
|
|
![]() |
|
Thread Tools | Display Modes |
![]() |
#1 |
Scooby Newbie
Member#: 4600
Join Date: Mar 2001
Chapter/Region:
MAIC
Location: Bel Air Subaru Nissan Group
Vehicle:Da Ridge Racer |
![]() I just bought a set of MOMO race pedals from PrimmRacing, and I can't figure out how to install the gas pedal. I know that I have to drill holes for the brake and the clutch pedals...that's easy. But the gas pedal is flat on both sides, and cannot be installed by itself. In other words, I have to drill holes in the FACTORY gas pedal, and install the MOMO pedal on top of it. I don't want to to that. Anyone got a solution?
Thanks Jazz95
* Registered users of the site do not see these ads.
|
![]() |
![]() |
![]() |
#2 |
Friendly Neighbourhood
Moderator Member#: 269
Join Date: Sep 1999
Chapter/Region:
VIC
Location: Burnaby, B.C., Canada
Vehicle:2005 ABP LGT LTD BP6 00 Impreza RS GM6 RIP |
![]() you got the superT pedals? They look like this?
![]() Then, yes you'll have to drill into the gas pedal. What I did to make the plastic pedal fit the "curve" of the Momo pedal is I heated the plastic pedal up with a heat gun, and then tried to "bend" it gently into the curve of the new pedal. Be careful that you don't snap or break your gas pedal - that'd be bad! ![]() Good luck! LaterZ! Darren!! |
![]() |
![]() |
![]() |
#3 |
Scooby Newbie
Member#: 4600
Join Date: Mar 2001
Chapter/Region:
MAIC
Location: Bel Air Subaru Nissan Group
Vehicle:Da Ridge Racer |
![]() No...I got the Racer pedals. Those are the ones I wanted though. But thanks for the advice. Looks like I'll be drillin' some more...
![]() Jazz95 |
![]() |
![]() |
![]() |
#4 |
Scooby Specialist
Member#: 4106
Join Date: Feb 2001
Location: Expected whp/torque at 25 psi : 450
|
![]() So do the factory pedals have a plastic cover on top of the metal pedal that you take off before the drilling , or do you drill over the plasic cover through the metal part ?
zaidoun |
![]() |
![]() |
![]() |
#5 |
Scooby Newbie
Member#: 4600
Join Date: Mar 2001
Chapter/Region:
MAIC
Location: Bel Air Subaru Nissan Group
Vehicle:Da Ridge Racer |
![]() Z,
The brake pedal and the clutch covers both come off. The gas pedal is one whole part though...hence my problem... ![]() Jazz95 |
![]() |
![]() |
![]() |
Thread Tools | |
Display Modes | |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
How to install new pedals? | LiDrummer | Newbies & FAQs | 4 | 10-03-2007 08:48 PM |
How to install new pedals on a 2006 STI | Jag32 | Interior & Exterior Modification | 4 | 06-30-2006 02:24 PM |
How to install new bulbs in '04 | rich22 | Newbies & FAQs | 9 | 01-05-2004 03:36 PM |
How to install new tranny? Clutch? Flywheel? | *-* | Transmission (AT/MT) & Driveline | 0 | 05-27-2003 01:41 AM |
00 2.5 how to install new rear speakers? | impresivesoob | Car Audio, Video & Security | 6 | 12-28-2002 11:55 PM |