|
|
|
|
Thread Tools | Display Modes |
10-11-2001, 05:03 PM | #1 |
Scooby Specialist
Member#: 2348
Join Date: Sep 2000
Chapter/Region:
MWSOC
Location: St.Louis
Vehicle:2006 WRX TR Steel Grey Metallic |
Where to tap for oil psi gauge?
Well, where should I tap it off of? the Turbo oil feed line, or somewhere else? Its an electrical Autometer gauge
* Registered users of the site do not see these ads.
|
10-11-2001, 05:15 PM | #2 |
Scooby Specialist
Member#: 759
Join Date: Jan 2000
Chapter/Region:
NESIC
Location: Warwick, RI
Vehicle:2012 Regal GS 2000 SV650 |
Shawn.......you have mail . It's kinda big, but hopefully it will help out.
Nat ---Actually Shawn, I guess you don't have mail. I thought the old board showed email addresses. Anyway, email me at [email protected] so I can reply and I'll send you a hand drawn diagram of parts and how to do it. |
10-11-2001, 05:28 PM | #3 |
Scooby Newbie
Member#: 4540
Join Date: Feb 2001
Vehicle:MY00 2.5RS Sedan Abnormally Aspirated |
You could tee off right where the stock pressure sender is mounted. You have to take off the alternator to get at it, though.
|
10-11-2001, 06:11 PM | #4 |
Former Vendor
Member#: 1990
Join Date: Jul 2000
Location: San Diego, CA
|
Take a look at the second picture down on this page. Look for number 3 circled in red. Right above that is where I put my Oil Pressure Sendor.
That location is on the passenger side right below the throttle body and intake manifold. If you already have a line coming out of there for the Turbo you can just "T" off of that. I guess that would be your Turbo Oil Feed line. I also have a Electrical Autometer Guage as one can see... |
10-11-2001, 11:56 PM | #5 |
Scooby Specialist
Member#: 4520
Join Date: Feb 2001
Location: LAS VEGAS
Vehicle:93 STi V.4 RA www.flat4lv.com |
Nat, can you please E-mail me that info also? I have the same question. Thanks, LVSUBARU@CS>COM
|
10-12-2001, 09:18 AM | #6 |
Scooby Specialist
Member#: 2348
Join Date: Sep 2000
Chapter/Region:
MWSOC
Location: St.Louis
Vehicle:2006 WRX TR Steel Grey Metallic |
NAT, e-mailed you...thanks guys..non of you know how to wire an ITC do you?
|
10-12-2001, 11:19 AM | #7 |
Scooby Specialist
Member#: 8488
Join Date: Jul 2001
Location: Sin City
Vehicle:1993 Impreza GCStyle Teal |
The picture in the thread on where to tap for a boost guage also shows where the oil line comes off the block. This is what The Dabbler was refering to.
http://i-club.com/forums/showthread....threadid=99123 Chad 93 1.8T |
10-12-2001, 02:44 PM | #8 |
Scooby Specialist
Member#: 2348
Join Date: Sep 2000
Chapter/Region:
MWSOC
Location: St.Louis
Vehicle:2006 WRX TR Steel Grey Metallic |
thanks
|
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Where to tap for oil pressure gauge? | joltdudeuc | Normally Aspirated Powertrain | 9 | 04-11-2006 09:46 PM |
where to tap for mech. boost gauge | monzon | Electrical & Lighting | 6 | 12-17-2005 07:17 AM |
Where to Tap for Boost Gauge Dimmer? | USF97J4x4 | Electrical & Lighting | 10 | 11-30-2005 11:04 AM |
Where to tap for positive gauge wire? | xq89olp | Electrical & Lighting | 5 | 07-05-2005 08:54 PM |
Where to tap for Turbo Oil inlet. | Unsung Boxer | Normally Aspirated with bolt-on Forced Induction Powertrain | 3 | 08-17-2003 07:53 PM |