Official Legacy Part # thread

[nedalrabadi]

any idea about the EJ20X ?
it was off a B4 LEGACY STI
i need to know about the head design is it like the EJ205 or the EJ207
the thing is i need pistons and i'm very confused should i get off the shelf pistons like the wrx or custom like the jdm ones

* Registered users of the site do not see these ads.

[krishnakodali]

I am gonna buy Subaru Legacy 2013.

Is it worth buying subaru navigation system ?

[faded-a-fool]

Originally Posted by krishnakodali

I am gonna buy Subaru Legacy 2013.

Is it worth buying subaru navigation system ?

Subaru has improved the Navigation system in the 2013's. I think it would be a better value to get an aftermarket nav. If you want to retain the stock look, then it's best to invest in the OEM nav.

[robinhood2688]

Hello i was wondering i have a 1990 subaru legacy l and i am in need of the clutch cable that goes from the pivot point into the transmission. Its a 5 speed 4 cylinder..i keep finding the one that goes from the pedal to the pivot point but my other one is shot any help with what the part is called or where i could find it? Thanks in advance for ur time

[H6STi80Y]

Can you please tell me the part numbers to these tailights set on this BH please

[omaid amiri]

Hello i am looking for 1997 legacy jdm front bumper and complete radiator support

[98leggygt]

I'm in need of a down pipe off of a 1989-1993 legacy turbo. And I can't seem to find any online. Does anyone know of any aftermarket one available? Or it would be easier if someone on here would have one to sell lol

[ChrisG961]

I'm in need of an ej25d for a 97 Legacy GT

[j13welder]

I just picked up a 99' legacy sus limited and I'm looking for an aftermarket intake, if anyone can point me in the right direction id appreciate it.

[Brisky]

NOTICE: Bilstein 24-101707 46mm Rear Struts have been discontinued by the manufacturer. Get them while you can.



Rear Strut Mounting Bolt Parts (for when it gets cross threaded on reinstall )

Part Description:
Rear Strut Mounting Flange Bolt

Model:
BE/BH

OEM Part Number:
901000177

List Price:
$5.90

----
Part Description:
Rear Strut Mounting Self Locking Nut

Model:
BE/BH

OEM Part Number:
20550AA010

List Price:
$7.78

----
Part Description:
Rear Strut Flange Bolt Washer

Model:
BE/BH

OEM Part Number:
900335056

List Price:
$1.73


------------------
Side Note:
The link the first post leads to a scammer/virus page thingy. DO NOT click it.

Use this instead:
http://opposedforces.com/parts/legacy/

[shainepepper]

Thanks

Originally Posted by xcntrk75

Model:
1998 2.5 GT Sedan (BD)


Part Description:
Front Hub
OEM Part Number:
28052AA010
Notes/Verification:
Often needed while replacing wheel bearing, this number is for an AT although they *should be the same as MT.

--------------------------------------------------

Part Description:
Front Ball-Joint
OEM Part Number:
21067GA050
Notes/Verification:
Direct fit, Right/Left side same.

--------------------------------------------------

Part Description:
Tie-Rod End
OEM Part Number:
34141AC010
Notes/Verification:
Direct fit, Right/Left side same.

--------------------------------------------------

Part Description:
Front Wheel Bearing (cartridge)
OEM Part Number:
28016AA011NT
Notes/Verification:
Entire bearing assembly, this is for an AT although they *should be the same.

--------------------------------------------------

Part Description:
Inner & Outer oil seals, wheel bearing.
OEM Part Number:
28015AA070
28015AA080
Notes/Verification:
Both inner and outer wheel bearing oil seal. One is pressed into hub before bearing, the other after.

--------------------------------------------------

Part Description:
Radio Bezel, wood grain
OEM Part Number:
J1310AC020
Notes/Verification:
BD, 2-DIN, Radio bezel in wood grain.

--------------------------------------------------

Part Description:
Power antenna replacement mast (rod nut assembly)
OEM Part Number:
86323AC070
Notes/Verification:
Part works great, easy to replace, make sure you don’t loose the tiny screws which hold the motor unit together, also may want to use some additional grease to help with the install.

[shainepepper]

Same here

Originally Posted by omaid amiri

Hello i am looking for 1997 legacy jdm front bumper and complete radiator support

[caymansubaru]

Hello, I am a new member and I have been searching the FAQ and looking around for a few parts for my dual turbo automatic legacy.

I recently replaced the vehicle's exhaust system, replaced the two wire catback o2 sensor with a three wire sensor. large amounts of black smoke are now coming from the tailpipe.

I think maybe the heated 3 wire sensor is throwing the computer off since it may be waiting for the nonheated values to be registered in order to do its fuel management thing. so I am planning to return the two wire sensor If I can find one. t

* Can someone please point me to a two-wire O2 sensor and a source for parts for a JDM Subaru legacy Thanks for any help.

[Patrick Olsen]

Do you have the old O2 sensor to try to pull a part number from?