|
|
|
|
Thread Tools | Display Modes |
06-24-2008, 11:05 PM | #1 |
Scooby Specialist
Member#: 181127
Join Date: May 2008
Chapter/Region:
Tri-State
Vehicle:1999 Civic Rust |
Is this ok?
... I just need to know how to bring the right down a bit...
* Registered users of the site do not see these ads.
|
06-24-2008, 11:10 PM | #2 |
Scooby Specialist
Member#: 173996
Join Date: Mar 2008
Chapter/Region:
MWSOC
Location: St. Louis, MO
Vehicle:2002 WRX WRB |
ehh its not too bad, not great but its workable.
|
06-24-2008, 11:17 PM | #3 |
Scooby Specialist
Member#: 181127
Join Date: May 2008
Chapter/Region:
Tri-State
Vehicle:1999 Civic Rust |
Its not as even but I want to point it down some more, I just can't find the leveling screws (If there are any!)
Maybe down and bit more wider... |
06-24-2008, 11:27 PM | #4 |
Scooby Newbie
Member#: 155938
Join Date: Aug 2007
Chapter/Region:
Tri-State
Location: yonkers, ny
Vehicle:2002 Impreza WRX WRB |
I wish I could help more, but it looks OK to me. Isn't the right side supposed to light up a bit higher on USDM headlights (left hand drive vehicles)? My EDM bugeyes are like that.
BTW, the thread title is vague. I just think it'd be helpful to elaborate for people searching who have similar questions. |
06-24-2008, 11:38 PM | #5 | |
Scooby Specialist
Member#: 181127
Join Date: May 2008
Chapter/Region:
Tri-State
Vehicle:1999 Civic Rust |
Quote:
Either ways, it took me a couple minutes to think of this title. Being drunk doesn't really help either. |
|
06-24-2008, 11:41 PM | #6 |
Scooby Newbie
Member#: 155938
Join Date: Aug 2007
Chapter/Region:
Tri-State
Location: yonkers, ny
Vehicle:2002 Impreza WRX WRB |
|
06-25-2008, 04:29 PM | #7 |
Scooby Specialist
Member#: 139076
Join Date: Jan 2007
Chapter/Region:
MAIC
Location: Scranton PA
Vehicle:2002 stg2 wagon 03 suzuki sv650s |
to aim your headlights properly, you need to park (on level ground) 25ft away from a wall.
measure the height of your projectors. on the wall, the middle of the beam step-up should be 1.8-2.0 inches lower than the height of your projectors. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
One intake valve is different on sti Heads, Is this ok? | STIStalker | Built Motor Discussion | 11 | 03-15-2010 12:59 PM |
Is this ok? | Genner | Newbies & FAQs | 6 | 06-02-2002 02:50 AM |
Is this ok place to tap for boost pressure reading | Fubaru | Factory 2.0L Turbo Powertrain (EJ Series Factory 2.0L Turbo) | 18 | 01-06-2002 10:53 PM |
Our MY01 RS...is this ok? | FLUBYUx2 | Interior & Exterior Modification | 6 | 10-02-2001 07:13 PM |