|
|
|
|
Thread Tools | Display Modes |
08-07-2007, 01:31 PM | #1 |
Scooby Newbie
Member#: 129979
Join Date: Oct 2006
Chapter/Region:
MWSOC
Location: Pville Illinois
Vehicle:2006 WRX TR vf39/ewg Black 310whp 360wtq |
need dump tube for ewg
my friend and i finished installing my new header, up-pipe and ewg. i have the tial 38mm ewg and it didnt come with a dump tube so its just venting into the engine bay. anyone know where i can get one at. i ordered my ewg from gruppe-s but it doesnt come with one and i couldnt find one to order on their site.
* Registered users of the site do not see these ads.
|
08-07-2007, 02:22 PM | #2 |
Scooby Specialist
Member#: 49978
Join Date: Dec 2003
Chapter/Region:
NESIC
Location: Shrewsbury, MA
Vehicle:2002 WRX w/ JDM STi 6spd, EJ255, VF39 & EWG |
What uppipe are you using? You can get a dump tube from UR for like $50 or $60 I think. It all depends on where the WG is located though. If you have a Helix uppipe I don't know if the dump tube will fit.
|
08-07-2007, 02:57 PM | #3 |
Scooby Newbie
Member#: 129979
Join Date: Oct 2006
Chapter/Region:
MWSOC
Location: Pville Illinois
Vehicle:2006 WRX TR vf39/ewg Black 310whp 360wtq |
i have the helix-v3. i havent found any dump tube so far. i might just have one fabricated.
|
08-07-2007, 07:15 PM | #4 |
Top Scoob 006
Member#: 14424
Join Date: Jan 2002
Chapter/Region:
South East
Location: Stuart, FL
Vehicle:BugI w/ 07 STi Swap www.TriStateTuners.com |
the helix uppipe already set up for ewg? uh oh... search around and you'll see that it lets the ewg dump right onto the power steering lines or axle, i forget which, and its so tight that there's no room to even put a dump tube in there.
that uppipe is best and only used in conjunction with the helix downpipe made to reroute the gases and the reroute kit from what i've read. i wanted to get one but decided to go custom instead after reading that... |
08-07-2007, 11:02 PM | #5 |
Scooby Specialist
Member#: 109084
Join Date: Mar 2006
Chapter/Region:
South East
Location: Oviedo, Fl
Vehicle:07 4EAT Forester 11.4 @118 |
The dumptube for the Helix uppipe is a tight fit but very doable, since I fabricated one myself (with a friends help). My car is also lowered, but the tube needed close to a 90 degree angle right off the wastegate to get it out of the way of the axle. It was a very poor design but it was also alot cheaper to go this route for me. On a lowered car like mine it is difficult but on one thats not lowered it may not be as hard. I might be able to get some pics of it on the car if you'd like?
|
08-08-2007, 02:07 AM | #6 |
Scooby Newbie
Member#: 129979
Join Date: Oct 2006
Chapter/Region:
MWSOC
Location: Pville Illinois
Vehicle:2006 WRX TR vf39/ewg Black 310whp 360wtq |
pics would help a lot if you can. if need be my neighbor owns a hot rod shop and i'll just have him fabricate one. but if you can get pics then please do.
|
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Flexible Dump Tube UR EWG Uppipe | motocooney | Car Part Reviews | 3 | 04-10-2010 11:06 AM |
WTB: Dump Tube for 44mm EWG (tial) | trex616 | Private 'Wanted' Classifieds | 2 | 04-28-2009 03:17 PM |
where can I get a dump tube for the helix V3 up pipe? | F ur PONY | Newbies & FAQs | 11 | 01-13-2009 03:09 AM |
Ultimate RAcing Uppipe with Dump tube for Tial 44MM EWG | Bariga | Engine/Power/Exhaust | 4 | 06-16-2008 11:04 PM |
WTB: Tial 44mm wastegate and uppipe for external, also needed, dump tube | AprilArchambeau | Private 'Wanted' Classifieds | 0 | 04-16-2008 06:40 PM |