|
|
|
|
Thread Tools | Display Modes |
07-31-2012, 11:29 AM | #3826 |
Scooby Specialist
Member#: 196013
Join Date: Nov 2008
Chapter/Region:
NWIC
|
I am at work so I don't have all the documentation with me, but I don't think you're too far off - especially since the JDM cars don't appear to have the other equipment from the factory. I guess what I was getting at was some people had complained because their drain valve or filter stopped working/became plugged, etc and they could no longer fill their gas tanks. I'm curious how if this is true I haven't had (and none of us have had) a problem with that if the JDM ECU doesn't do anything with this drain valve.
I haven't had any issues with anything, and mine has been running the JDM ECU since it was installed, never switched back for any reasons. I guess having a description of operation of the total system would be nice so I can see what does what. ~T.J. EDIT: Documentation I just found implies the drain valve (AKA Vent Control Solenoid Valve) is normally open and is driven closed by an ECU signal; same goes for the pressure control solenoid valve. The vent valve on the tank, is mechanical in nature I believe. This basically means the car defaults to all the electrical valves being open without ECU interaction. My only problem with this is that it means the car would be off gassing quite a bit of emissions from the tank on a hot day for instance, which I think is a no no, so I have a hard time believing this is correct for stock. However, if that IS correct, it would explain how it can all still work without excess tank pressure. If those valves default open, the excess pressure should be pulled to the intake by the purge valve as mentioned. This was found in another thread on Nasioc, listed as being for a 2000 RS. I can only assume operation would be similar.
* Registered users of the site do not see these ads.
Last edited by 02CWRX; 07-31-2012 at 12:39 PM. |
08-05-2012, 06:37 PM | #3827 |
Scooby Newbie
Member#: 246455
Join Date: May 2010
Chapter/Region:
SCIC
Location: CA
Vehicle:2004 WRX Wagon WRB |
Just a quick question... I have an EJ207 Ver. 8 motor and it has a slight knock/tap when the engine is started and it is cold. The sounds raises proportionally to engine rpms to about 2000, then i cannot hear it anymore. Once it gets the coolant and oil hot, the sound goes away all together. Could a rod/crank knock disappear when everything is hot?
Thanks Tom |
08-05-2012, 06:54 PM | #3828 |
Scooby Newbie
Member#: 230978
Join Date: Nov 2009
Chapter/Region:
MWSOC
Location: Cedar Falls, Iowa
Vehicle:2002 VF43 Stg III PSM |
I have the same thing on my ej205. It definately concerns me. It is much worse in the cold winter months. It sounds more like a valve issue so I called the local Subaru dealership to enquire. From the response I got i will assume () that they don't adjust valves. They quoted me some ungodly price so I searched the forum here. Not saying this is what you are hearing, but many report that their cars sound like boxes of rocks at start up, especially when cold. I would still like to have my valves adjusted though. The set up in these subies is very similar to a DOHC motorcycle engine.
|
08-05-2012, 09:25 PM | #3829 |
Scooby Specialist
Member#: 115297
Join Date: May 2006
Chapter/Region:
SWIC
Location: Mesa, AZ
Vehicle:2002 ej207 vf34 WRB |
A little noise is not uncommon, between the injectors clicking and valvetrain noise it can be a cacophonas symphony.
A little noise....ok, more than that and you might want to do a compression and leakdown to rule out any major issues. Has it always been like that? Have you tried different weights of oil? A heavier (or correct) oil can go a long way in quieting engine noise, though it ain't fix anything if something is amiss. |
08-05-2012, 10:44 PM | #3830 | |
Scooby Newbie
Member#: 246455
Join Date: May 2010
Chapter/Region:
SCIC
Location: CA
Vehicle:2004 WRX Wagon WRB |
Quote:
|
|
08-05-2012, 11:48 PM | #3831 | |
Scooby Specialist
Member#: 304662
Join Date: Dec 2011
Chapter/Region:
MAIC
Vehicle:2001 Impreza L coupe Sedona red Pearl |
Quote:
The person who this quote is from, said they have 230k+ miles on an ej22 with piston slap. As long is it doesn't get worse you'll be fine. Just take it real easy until the motor gets more warmed up. If it makes you feel better my motor has piston slap too. That and the injector noises seem to be pretty common. Last edited by ManualOverAuto; 08-06-2012 at 12:03 AM. |
|
08-07-2012, 02:35 PM | #3832 | |
Scooby Guru
Member#: 4414
Join Date: Feb 2001
Location: Dublin, CA
Vehicle:2002 WRX Sedan Midnight Black |
Quote:
It's common with most any Subaru engine that has significant miles on it, because generally a valve adjustment will be done by first pulling the engine due to the space restriction between the heads and the fenders. This makes valve adjustments pretty damn expensive. I think most charge ~8 book hours for pulling & replacing the engine before they even get to the valve adjustment parts & labor. My engine has had this for a LONG time. Probably 80 thousand miles or so, but I don't really remember when I first noticed it making that noise on warm-up. The engine has 180k total miles, so it's generally not something that will kill the engine, just another thing to remind you not to beat on the engine until everything is fully up to temp. Most just live with the valve tap, as the price for a valve adjustment is a tough pill to swallow. |
|
08-07-2012, 05:31 PM | #3833 |
Scooby Specialist
Member#: 237145
Join Date: Feb 2010
Chapter/Region:
SCIC
Location: 562
Vehicle:02 WRX 12 FXT |
So I have a question. How would you make the EJ207 swap legal in California?
I see it needs to be a newer model and same type of engine? How do you get them to pass with the obdII and sniffer? |
08-07-2012, 05:49 PM | #3834 |
Scooby Specialist
Member#: 115297
Join Date: May 2006
Chapter/Region:
SWIC
Location: Mesa, AZ
Vehicle:2002 ej207 vf34 WRB |
California sucks.....from what I've read its possible but will require quite a bit of work (fooling the inspectors.)
At a minimum you'd need to run your USDM ECU for the OBD II test, which means you'll need it tuned on that ECU, or at least it will have to run well enough on it to pass the sniffer. That's what I plan on doing when mine are due. But I've heard of people in AZ passing on the jdm ECU. I'll run my usdm just to be safe. FWIW my Innova OBD II scanner says "pass" on my jdm ECU, on the "OBD II readiness. |
08-07-2012, 06:15 PM | #3835 |
Scooby Specialist
Member#: 237145
Join Date: Feb 2010
Chapter/Region:
SCIC
Location: 562
Vehicle:02 WRX 12 FXT |
So can I run perfectly fine on my usdm ecu after being tuned in OS? or is swapping ecu's from different markets bad?
|
08-07-2012, 06:30 PM | #3836 |
Scooby Specialist
Member#: 115297
Join Date: May 2006
Chapter/Region:
SWIC
Location: Mesa, AZ
Vehicle:2002 ej207 vf34 WRB |
It will depend on the tunes on each ECU.
If say you had a vf39 on your ej205 and you ran the vf37 on the ej207, the tunes would be close enough that you could swap in your usdm ECU and run it (for a short time) and you would be ok. It would not be advised to do wot pulls but it should run close enough that you could pass through emissions. But it all depends on the tuned components on each ECU. Mine are close enough that I can swap them and the usdm runs fine (no avcs obviously). |
08-07-2012, 06:30 PM | #3837 |
Scooby Guru
Member#: 4414
Join Date: Feb 2001
Location: Dublin, CA
Vehicle:2002 WRX Sedan Midnight Black |
Stock ECU will run the EJ207, but will not use the AVCS. You want to run the JDM ECU so you can run the AVCS, as this adds significant off-boost torque and throttle response. However, you want your USDM ECU for the SMOG test. You just swap ECUs and go to the SMOG place. USDM stock mapping won't break anything, assuming you are easy on the gas.
You will need someone to re-flash a map to your USDM ECU that defeats the readiness monitors. Otherwise, when you hook up your USDM ECU, you'll need to drive around several hundred miles first. Anyone with a Tactrix should be able to download your ECU map and turn off the readiness monitors and flash it back. 10 minute job. I still don't think that's technically "legal" in California, but it should pass SMOG assuming the rest of your setup is going to pass the pipe and visual test. |
08-07-2012, 09:00 PM | #3838 | |
Scooby Specialist
Member#: 259970
Join Date: Oct 2010
Chapter/Region:
Tri-State
Location: brewster, NY
Vehicle:2002 wrx cobb stg2+ psm proper fitment |
Quote:
|
|
08-07-2012, 09:53 PM | #3839 |
Scooby Specialist
Member#: 237145
Join Date: Feb 2010
Chapter/Region:
SCIC
Location: 562
Vehicle:02 WRX 12 FXT |
Thanks Concillian.
I am now a step back from getting a jdm engine. Wastegate arm on the td04 was loose and I was not hitting my target 20 psi. And I'm doing a compression check tomorrow. I just wanted to know if there was still hope for a jdm engine in California |
08-07-2012, 10:51 PM | #3840 | ||
Scooby Guru
Member#: 4414
Join Date: Feb 2001
Location: Dublin, CA
Vehicle:2002 WRX Sedan Midnight Black |
Quote:
The fact that the ECU pinout is the same (aside from additional pins for AVCS on the JDM ECU) is one of the big reasons people do this swap in the first place. Here's what Crawford / i-speed had to say about things when they were swapping these into older 2.5 RS cars and getting them past the ref as an 02+ WRX: Quote:
Last edited by Concillian; 08-07-2012 at 10:59 PM. |
||
08-08-2012, 07:37 AM | #3841 |
Scooby Guru
Member#: 46135
Join Date: Oct 2003
Chapter/Region:
Tri-State
Location: NY
Vehicle:19 GLA45 AMG C63 AMG |
My tune on my USDM ECU makes it very likely to stall, when I use it.
I have adressed the MAF, the fueling, tables, etc. But if I let it learn the trims, it does OK. Of course, I don't ask any kind of performance from this ECU, drive out of boost, AVCS disconnected at the solenoids. |
08-08-2012, 09:51 AM | #3842 |
Scooby Specialist
Member#: 86107
Join Date: Apr 2005
Chapter/Region:
E. Canada
Location: 10% REAL FRUIT JUICE
|
dyno next week for me.
I'll post the numbers up ! |
08-08-2012, 04:30 PM | #3843 |
Scooby Specialist
Member#: 115297
Join Date: May 2006
Chapter/Region:
SWIC
Location: Mesa, AZ
Vehicle:2002 ej207 vf34 WRB |
Quick question for guys who are running the stock twinscroll headers and uppipe....
Is it better to leave the heat shielding on, or take it off and wrap them? Which has better heat retention? If it's better to wrap, should I wrap the flex section on the headers? I've seen some guys skip this area. I'm finally taking the plunge and building a vf36 (almost) from my vf34 and a vf36 turbine housing that I found. Seems to be possible. Worst case scenario I use my vf37. This should be the best of both worlds....roller bearing and twinscroll!! Hoping to have the quickest spooling 300hp DD. Still waiting for EDO to get in some TS downpipes....anyone know who else sells these? I'd rather have a professionally built pipe than weld two together. thanks. |
08-08-2012, 05:20 PM | #3844 |
Scooby Specialist
Member#: 175334
Join Date: Mar 2008
Chapter/Region:
TXIC
Location: Dallas, TX
Vehicle:2003 Impreza WRX JDM v8 EJ207 WRB |
^^ yeah, it'd be really nice to get a Spec C with VF36. I've been drooling at the prospect of how it would be as a daily, on a well sorted setup. Here's a dyno comparison 'K1WRC' posted between his VF34'd EJ205 & VF36'd EJ207 (from page 143) that i've been obsessing over
|
08-08-2012, 06:19 PM | #3845 |
Scooby Guru
Member#: 4414
Join Date: Feb 2001
Location: Dublin, CA
Vehicle:2002 WRX Sedan Midnight Black |
Moore Performance at least has a prototype stock location TS DP out there. Perhaps give them a ring on when they'll be ready for prime-time.
|
08-08-2012, 07:11 PM | #3846 |
Scooby Specialist
Member#: 315635
Join Date: Apr 2012
Vehicle:04 STi Aspen White |
would you guys say that these numbers seem normal ? or should i be able to pull more outa the motor?
ej207 v7 with: stock vf30 stock pinks pinjectors walbro 255lph fmic 3" turbo back exhaust equal length headers w/ up-pipe hks ssq b.o.v dyno tuned to 306awhp / 292lb of torque |
08-08-2012, 07:14 PM | #3847 |
Scooby Specialist
Member#: 115297
Join Date: May 2006
Chapter/Region:
SWIC
Location: Mesa, AZ
Vehicle:2002 ej207 vf34 WRB |
I would be thrilled with those numbers, but more importantly are you happy with how it feels?
Numbers don't always tell you what's going on. There is always room for more power, but it comes down to diminishing returns. |
08-08-2012, 07:31 PM | #3848 |
Scooby Specialist
Member#: 115297
Join Date: May 2006
Chapter/Region:
SWIC
Location: Mesa, AZ
Vehicle:2002 ej207 vf34 WRB |
Just noticed that dip after peak...what's that about?
Do you have a boost and AFR graph as well? |
08-08-2012, 07:39 PM | #3849 |
Scooby Specialist
Member#: 271412
Join Date: Jan 2011
Chapter/Region:
Tri-State
Location: avoca pa
Vehicle:05 ej207 wrx wagon wrb |
numbers seem good to me.
i put down 310whp/288tq on efi logics mustang dyno. 21psi v7 vf30,intake,3in turbo back,pinks,255,turbo inlet,uel headers,sti tmic |
08-08-2012, 07:54 PM | #3850 |
Scooby Specialist
Member#: 315635
Join Date: Apr 2012
Vehicle:04 STi Aspen White |
i am satisfied with how it feels in its middle range rpm's but i need a ebcs to help spool.
it feels strong when its in its sweet range of rpm's and i ran a 1/4 mile in just under the 12.9 with a decent but could be better reaction time. the dip concerns me as well but i find it common in thew print out graphs from this tuner, it does drive fine tho. this tune is on 91 pump gas too btw |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
ej207 owner wants opinions | adbramsay | Factory 2.0L Turbo Powertrain (EJ Series Factory 2.0L Turbo) | 2 | 02-26-2011 07:29 PM |
Ej207 V6 | AndrewFD3 | Factory 2.0L Turbo Powertrain (EJ Series Factory 2.0L Turbo) | 10 | 06-03-2010 04:53 PM |
JDM Sti EJ207 V9 crank 75mm or billet crank (K1, Manley) VENDORS ??? | L'frise | Private 'Wanted' Classifieds | 7 | 06-03-2010 09:24 AM |
08 ej207 JDM dual AVCS heads on a built v7 ej207 | icev7 | Built Motor Discussion | 17 | 02-21-2010 03:21 PM |
Ver 8 EJ207 Owners Check In | spoolinsuby | Factory 2.0L Turbo Powertrain (EJ Series Factory 2.0L Turbo) | 21 | 10-17-2005 01:56 AM |