Welcome to the North American Subaru Impreza Owners Club Tuesday December 11, 2018
Home Forums WikiNASIOC Products Store Modifications Upgrade Garage
NASIOC
Go Back   NASIOC > NASIOC Technical > Engine Management & Tuning > AccessPort

Welcome to NASIOC - The world's largest online community for Subaru enthusiasts!
Welcome to the NASIOC.com Subaru forum.

You are currently viewing our forum as a guest, which gives you limited access to view most discussions and access our other features. By joining our community, free of charge, you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is free, fast and simple, so please join our community today!

If you have any problems with the registration process or your account login, please contact us.
* Registered users of the site do not see these ads. 
Reply
 
Thread Tools Display Modes
Old 06-11-2014, 04:41 AM   #1
ncsketch
Scooby Newbie
 
Member#: 393332
Join Date: Jun 2014
Default Failed Accessport Install

I'm new around here but i've done a ton of lurking and reading and i've spent the past 3 hours trying to figure this out. My problem is that the Acceesport will not go beyond the screen that says "Verify that ignition switch is in the ON position"

I put the keys in the off position, plugged in OBD cable, plugged the other end to the AP and then turned the keys to the on position.

I've checked that every thing is nice and tight. door is shut lights are off stereo fans etc. they are all off.

Also once i gave up I turned the car off unplugged everything and now when i turn it on i have a CEL, SI-Drive light blinking [s], and the cruise control light flashing.

the car runs weird.

What are my next steps.

yes Accessport is up to date

CliffNotes
- CEL after failed AP install
- AP doesn't go passed the check to make sure ignition is in the on position.
- 14 STI
* Registered users of the site do not see these ads.
ncsketch is offline   Reply With Quote
Sponsored Links
* Registered users of the site do not see these ads.
Old 06-11-2014, 05:51 AM   #2
m71owner
Scooby Specialist
 
Member#: 332321
Join Date: Sep 2012
Location: grand rapids mi
Vehicle:
1998 2.5rs
wrb

Default

Which ap are you using?
m71owner is offline   Reply With Quote
Old 06-11-2014, 09:55 AM   #3
ncsketch
Scooby Newbie
 
Member#: 393332
Join Date: Jun 2014
Default

V3 oo3
ncsketch is offline   Reply With Quote
Old 06-11-2014, 11:58 AM   #4
LIChuck
Scooby Specialist
 
Member#: 266122
Join Date: Dec 2010
Chapter/Region: Tri-State
Location: Patchogue, NY
Vehicle:
2007 WRX Limited
UGM

Default

Never mind.

Last edited by LIChuck; 06-11-2014 at 04:40 PM.
LIChuck is offline   Reply With Quote
Old 06-11-2014, 01:42 PM   #5
Joshfl420
Scooby Specialist
 
Member#: 353788
Join Date: Apr 2013
Chapter/Region: South East
Location: S Florida
Vehicle:
1997 Cherokee
Tuned by AlanSnackbar

Default

Note - The 2008+ WRX/STI do not need to have the test connectors connected as stated in the instruction booklet to install the AccessPORT. These vehicles will automatically go into test mode thanks to the CAN BUS protocol.
Joshfl420 is offline   Reply With Quote
Old 06-11-2014, 01:49 PM   #6
wgr73
Scooby Specialist
 
Member#: 232458
Join Date: Dec 2009
Chapter/Region: SWIC
Location: Las Cruces/El Paso
Vehicle:
2005 & 2008 STi
Cobb 20g & EFR 7670

Default

Contact Cobb.

Also, go to an Autozone and pull the codes it's throwing. Post those up here
wgr73 is offline   Reply With Quote
Old 06-13-2014, 12:49 AM   #7
ncsketch
Scooby Newbie
 
Member#: 393332
Join Date: Jun 2014
Default

took it to Subaru it was a blown fuse.
ncsketch is offline   Reply With Quote
Old 10-28-2018, 02:50 AM   #8
BD 04STI
Scooby Newbie
 
Member#: 487103
Join Date: Jun 2018
Default

Quote:
Originally Posted by ncsketch View Post
took it to Subaru it was a blown fuse.
I really hate to bring back an old thread but Im stuck in having the same problem but my car won’t even start. What fuse was it?
BD 04STI is offline   Reply With Quote
Old 10-28-2018, 08:49 AM   #9
Charlie-III
NASIOC Supporter
 
Member#: 30669
Join Date: Dec 2002
Chapter/Region: Tri-State
Location: USA, North NJ, 07456
Vehicle:
1998 Legacy 2.5GT
Silver Sleeper BK, 5MT

Default

Quote:
Originally Posted by BD 04STI View Post
I really hate to bring back an old thread but Im stuck in having the same problem but my car won’t even start. What fuse was it?
Just meter them all under the hood and dash. Likely a 10A or lower.
Do you have the same year/model car and AP?
Charlie-III is offline   Reply With Quote
Old 10-28-2018, 01:32 PM   #10
BD 04STI
Scooby Newbie
 
Member#: 487103
Join Date: Jun 2018
Default

Quote:
Originally Posted by Charlie-III View Post
Just meter them all under the hood and dash. Likely a 10A or lower.
Do you have the same year/model car and AP?
2004 sti AP3
BD 04STI is offline   Reply With Quote
Old 10-30-2018, 10:56 AM   #11
Charlie-III
NASIOC Supporter
 
Member#: 30669
Join Date: Dec 2002
Chapter/Region: Tri-State
Location: USA, North NJ, 07456
Vehicle:
1998 Legacy 2.5GT
Silver Sleeper BK, 5MT

Default

Quote:
Originally Posted by BD 04STI View Post
I really hate to bring back an old thread but Im stuck in having the same problem but my car won’t even start. What fuse was it?
Quote:
Originally Posted by BD 04STI View Post
2004 sti AP3
Does the car crank?
Did you get the AP to marry, or not?
Is this a new AP or used?
Charlie-III is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

All times are GMT -4. The time now is 09:44 PM.


Powered by vBulletin® Version 3.7.0
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
Powered by Searchlight © 2018 Axivo Inc.
Copyright ©1999 - 2017, North American Subaru Impreza Owners Club, Inc.