|
|
|
|
Thread Tools | Display Modes |
04-02-2013, 02:08 PM | #701 |
Scooby Newbie
Member#: 174930
Join Date: Mar 2008
Location: Virginia Beach VA
Vehicle:2002 WRX Silver |
Hmm, just realized your probably not using the default forum post count per page. Which means I've replied twice to a useless post...
* Registered users of the site do not see these ads.
|
04-02-2013, 02:11 PM | #702 |
Scooby Guru
Member#: 48219
Join Date: Nov 2003
Chapter/Region:
MAIC
Location: Pittsburgh, PA
Vehicle:. Always drive the race line . |
I brainstormed some a while back but never actually tested it. The thing is, it depends on what kind of spring you have in the EWG. The problem I had was the spring was so weak, it would blow open even without anything connected to the EWG ports. I wouldn't be able to run more than 16psi on a 2.5L.
I was going to buy a second MBC and have it only control pressure to the top port while keeping the rest of the hybrid boost control system in place as is. But then I inadvertently installed an inspection window on top of the block and got more busy with life etc. Try this, install a secondary MBC as a 'tee' in the line going from compressor to top port. Tune the MBC to regulate pressure in the top port. Send the other end of this MBC back to the intake or atmosphere. Then connect the EBCS and MBC as stated in this thread to the side port. Last edited by MRF582; 04-02-2013 at 02:17 PM. |
04-02-2013, 02:13 PM | #703 |
Scooby Guru
Member#: 32792
Join Date: Feb 2003
Chapter/Region:
NESIC
Location: lincoln, ri
Vehicle:2003 GGA MBP 12.9 / 105+ |
question is, what is the goal?
|
04-02-2013, 02:15 PM | #704 |
Scooby Newbie
Member#: 174930
Join Date: Mar 2008
Location: Virginia Beach VA
Vehicle:2002 WRX Silver |
|
04-02-2013, 02:16 PM | #705 | |
Scooby Newbie
Member#: 174930
Join Date: Mar 2008
Location: Virginia Beach VA
Vehicle:2002 WRX Silver |
Quote:
spring is currently ~6psi |
|
04-03-2013, 04:13 PM | #706 |
Scooby Newbie
Member#: 174930
Join Date: Mar 2008
Location: Virginia Beach VA
Vehicle:2002 WRX Silver |
Got it figured out, thanks.
|
04-29-2013, 12:39 PM | #707 |
Scooby Specialist
Member#: 282614
Join Date: May 2011
Chapter/Region:
NWIC
Location: Spokane Washington
Vehicle:2006 Wrx sti Black pearl |
Would it be possible to do this hybrid set up with a grimmspeed 3 port and a greddy profec b type s mbc. I have my car tuned for the 3 port now and am planing on doing a ewg for my next tune. My car had the profec b type s mbc in it while ago and is now just sitting in my car not functioning just needs the boost lines ran. So I was just curious if this combo would work so the mbc isn't just sitting in my car to look cool.
|
04-29-2013, 02:14 PM | #708 | |
Scooby Specialist
Member#: 118630
Join Date: Jun 2006
Chapter/Region:
South East
Vehicle:2005 Wrx wagon Red |
Quote:
The original poster installed a cockpit adjustable Manual boost controller so he was able to set the max boost level from inside the car, then through all the stuff on the ECU and with the 3-port system he was able to control all of the partial throttle boost levels. The 3 knobs on your Profec allow you to do essentially the same thing even if you're not able to set specific limits per throttle input and RPM. If you read through most of these posts, 80% of the guys using hybrid aren't worried about specific partial throttle boost limits anyway and just look for a linear taper of boost at any given throttle input with a max boost level for WOT. The Profec can certainly do that for you and then some, it's just a slightly different way of achieving the same result. It's only because a full standalone is a tad expensive and not integral to the OEM setup that this whole topic exists. |
|
04-29-2013, 06:32 PM | #709 | |
Scooby Guru
Member#: 32792
Join Date: Feb 2003
Chapter/Region:
NESIC
Location: lincoln, ri
Vehicle:2003 GGA MBP 12.9 / 105+ |
Quote:
|
|
04-29-2013, 11:19 PM | #710 |
Scooby Specialist
Member#: 282614
Join Date: May 2011
Chapter/Region:
NWIC
Location: Spokane Washington
Vehicle:2006 Wrx sti Black pearl |
It will just be on my stock vf39. I'm just looking to get away from overboosting I had it protuned with the 3 port and have had a few versions of my maps to help with the issue and so far nothing has worked so my next step is ewg. The iwg will be closed with the cobb adjustable Watergate arm. I'll look into that tho I just want the most efficient way to control my boost. I had the mbc hooked up when I first bought my car and it was a big pain so I just opted for another protune with the 3port. I just saw this and thought I might be able to utilize my mbc for better boost control but sounds like just running a 3 port with my ewg will be my best bet.
|
04-30-2013, 07:07 AM | #711 |
Scooby Guru
Member#: 32792
Join Date: Feb 2003
Chapter/Region:
NESIC
Location: lincoln, ri
Vehicle:2003 GGA MBP 12.9 / 105+ |
the key advantage of using an mbc in parallel is that it utterly eliminates boost control overshoot.
if you have a physical issue causing boost creep, ie, not enough wastegate flow, then it will not help. you would be able to discern the difference by running the vf39 with the mbc and seeing if you're able to clamp boost to your target without overshoot. running iwg and ewg in parallel gives you the ability to drive stealthily at partial throttle, while a VTA ewg gives you max VE (and noise) at WOT. |
04-30-2013, 07:29 AM | #712 |
Scooby Guru
Member#: 103232
Join Date: Dec 2005
Chapter/Region:
Tri-State
Location: GTX3576R 05GD, GTX3076R'd FXT
Vehicle:GTX 3071R'd 11WRX PPG,4.44,LSD,E85,6spdx3 |
Is anyone gunning their IWG with a VTA EWG?
|
04-30-2013, 09:13 AM | #713 |
Scooby Specialist
Member#: 254163
Join Date: Aug 2010
Chapter/Region:
MAIC
Location: MD
Vehicle:2011 WRX 20GXTR Black |
-wrong thread. Stupid phone.
|
04-30-2013, 09:53 AM | #714 | |
Scooby Specialist
Member#: 118630
Join Date: Jun 2006
Chapter/Region:
South East
Vehicle:2005 Wrx wagon Red |
Quote:
By looking at the Profec installation diagram, it looks like the Profec Valve unit is a 2 port interrupt setup. That should make running a ball MBC parallel that much easier because there's no 3rd VTA port to block off. Worth a shot I suppose. Do we know if the valve unit on the Profec is an oscillating solenoid or a butterfly valve? |
|
04-30-2013, 11:22 AM | #715 | |
Scooby Specialist
Member#: 282614
Join Date: May 2011
Chapter/Region:
NWIC
Location: Spokane Washington
Vehicle:2006 Wrx sti Black pearl |
Quote:
|
|
04-30-2013, 03:03 PM | #716 | |
Scooby Guru
Member#: 32792
Join Date: Feb 2003
Chapter/Region:
NESIC
Location: lincoln, ri
Vehicle:2003 GGA MBP 12.9 / 105+ |
Quote:
there is no reason why your car should have uncontrollable boost creep past 20psi. if you already own the mbc, and the car is already (mostly) tuned on the 3 port and oem ecu, then for the price of two tees and a bit of hose you can try it out. |
|
04-30-2013, 04:31 PM | #717 |
Scooby Specialist
Member#: 118630
Join Date: Jun 2006
Chapter/Region:
South East
Vehicle:2005 Wrx wagon Red |
Well, you have to adjust the "SET" value on the Profec if you're overboosting that much, the Gain isn't going to fix the amount of overboost you're running into. The target boost level is just a target which the Profec isn't going to automatically figure out how to hit.
http://www.greddy.com/upload/file/PRofec_Bspec2.pdf The "SET" mode on the profec is essentially the same as the subaru control for max wastegate duty cycle. The gain is just the rate at which corrections are applied but unlike the subaru control you can also bump up the duty cycle past the max value by adjusting the gain really high. You can also essentially reduce the max duty cycle which reduces boost by turning it lower. However, before gain begins to adjust the on-target duty cycle values up or down you have to have a SET value dialed in for on-target boost. If the SET value is higher than your target requires (like yours must be right now causing overboost) the Gain will not be able to subtract enough duty cycle to get back down to target. Anyway, by introducing an MBC to the setup you can max out your SET value which maxes the spoolup time and you can use the gain to adjust the partial throttle and spool up rates as you've been trying to instead. Here's how you'd tee in the MBC to your profec boost lines on your car. Once you do this, you can simply max out the SET value on your Profec unit and set the target boost on the profec, over a couple WOT pulls you can set the max boost on the MBC (start with the MBC knob really loose to undershoot your target and make small adjustments until you make target). Once the max boost on the MBC is done, you can go into the profec, and from say, 50% SET begin to increase the SET value so you hit max boost in your desired gear, I'd choose 3rd but you could leave the SET to 100% to leave it at full MBC control which could yield max boost in 1st or 2nd depending on your turbo Then you should be able to control the boost spoolup with the gain knob as you've been trying to. You can use the SET value to reduce the max boost below the MBC as well. Since also have a "low boost" mode on the Profec. If you dial that in you can have a separate lower boost limit with the MBC on the car too. Pretty sweet. Last edited by BrandonDrums; 04-30-2013 at 04:49 PM. |
05-01-2013, 01:10 AM | #718 | |
Scooby Specialist
Member#: 282614
Join Date: May 2011
Chapter/Region:
NWIC
Location: Spokane Washington
Vehicle:2006 Wrx sti Black pearl |
Quote:
Also sorry I just looked at that link you posted just now and that unit is not the same as mine. Its profec type c. I think the only difference is that the set on the type 2 is the same as the high and low boost on the type c. I could be wrong tho Last edited by Coreycarlile911; 05-01-2013 at 01:46 AM. |
|
05-01-2013, 02:31 PM | #719 | |
Scooby Specialist
Member#: 118630
Join Date: Jun 2006
Chapter/Region:
South East
Vehicle:2005 Wrx wagon Red |
Quote:
I have no idea about the 3 knob one. I know you can hook up the hoses the same way as my diagram but as far as programming it I haven't a clue. FYI, Standalone boost control systems like your Greddy/Profec one are manual ELECTRONIC boost controllers. The only real difference between them and the factory boost system is that they have an electronic module with different logic for tuning boost. They still rely on a 2 port interrupt solenoid valve to work which is the same thing as a 3 port solenoid with the bleed valve capped (like in the hybrid boost control setup). Adding a ball and spring manual boost controller in parallel with the valve unit from the profec system will work the same way as it does with the 3 port boost controller on the factory setup. Hopefully someone more familiar with your profec unit can tell you how to set that up correctly. Here's the manual for it, I can't make heads or tails of how to address the overboost you're having though. http://www.greddy.com/upload/file/PRofec_Bspec.pdf |
|
05-28-2013, 09:15 PM | #720 |
Scooby Newbie
Member#: 299442
Join Date: Oct 2011
Location: Southern Ontario Canada
Vehicle:2005 Forester XT |
Hey guys, I posted this in the 2.5 powertrain cause of the inceased traffic but Ill give it a try here too.
Im in the process of getting tuned for a hybrid boost control setup and some larger injectors. I am running a Grimmspeed ebcs and a Grimmspeed mbc. I am getting over boost and I cannot seem to fix the problem. My tuner has my wastegate duty cycle set to zero at the moment so that we can dial in the mbc and what I should be seeing is just wastegate pressure of 14 psi. The car is peaking around 18.5 psi on thrid gear pulls even with the mbc backed all the way off. I have plugged off the number 1 port on the ebcs and the the nipple it fed to on the turbo inlet. I have also plugged the bleed hole on the mbc which was recomended in this setup to prevent over boost. Everything else is tight and all lines are zip tied, Im really not sure what to check next. The only thing I can possible think is the issue is that the way I blocked off the bleed hole on the mbc is still leaking. It did seem to drive better after I did it but perhaps its not perfect. Anyone who has a good way of blocking off the bleed port Id love to hear it. |
05-28-2013, 09:25 PM | #721 |
Scooby Specialist
Member#: 50699
Join Date: Dec 2003
Chapter/Region:
TXIC
Location: austin
Vehicle:2004 WRX Platinum Silver |
Did you try just running the mbc or even just a straight house from the nipple to the WG? Eliminate everything then add in the mbc and then the ebc.
If the ebc is wired backward than your zero could be seen as 100% instead. Hose length can effect the issue. And ideally you would want to set the ebc to 100% to give the control over to the MBC. I had a similar issue initially but the plug on the 3rd port is what fixed my spikes. Has your tuner done a hybrid boost control setup before? Also there have been several posts on here with the diagram. Try posting up how you did yours so we can take a look |
05-28-2013, 09:55 PM | #722 |
Scooby Newbie
Member#: 299442
Join Date: Oct 2011
Location: Southern Ontario Canada
Vehicle:2005 Forester XT |
Thanks for trying to help me out!
That will be my next step is to run just the mbc and see what happens, I had never thought of that if it is being read wrong and the Watergate duty should actually be 100%. http://forums.nasioc.com/forums/show....php?t=2158005 The diagram in the first post is how a set mine up but I have capped off the number one port and the nipple on the inlet it would feed to. |
05-28-2013, 10:18 PM | #723 | |
Scooby Specialist
Member#: 118630
Join Date: Jun 2006
Chapter/Region:
South East
Vehicle:2005 Wrx wagon Red |
Quote:
If the tuner really is trying to setup the MBC with wgdc set to zero, chances are he doesn't understand how the boost control system works and has the hoses routed incorrectly. If he has it set to 100 and everything routed correctly and the MBC isn't controlling boost then the MBC is clogged, there's a leak or the wastegate actuator or wastegate itself is seized. I had a faulty Wastegate actuator on a brand new turbo once, it was too weak rather than too strong or seized up but it can happen. |
|
05-29-2013, 07:26 AM | #724 |
Scooby Specialist
Member#: 221364
Join Date: Aug 2009
Chapter/Region:
MAIC
Location: Baltimore
Vehicle:2002 Wrx EJ207 Ver 8 Wrb Dccd jdm 6 speed now! |
Me and my tuner just set up my car yesterday with a prodrive 3 port and turbosmart mbc, we followed the setup from the first page. It works perfectly . So either it's hooked up wrong or the ebcs or mbc is broken. I would try to set up just the mbc and get that sorted first.
|
05-29-2013, 10:31 AM | #725 |
Scooby Guru
Member#: 32792
Join Date: Feb 2003
Chapter/Region:
NESIC
Location: lincoln, ri
Vehicle:2003 GGA MBP 12.9 / 105+ |
while troubleshooting boost control, always start with single unobstructed hose straight from compressor to wga. this will net wastegate spring tension. it should be absolutely rock steady with no creep or overshoot or ringing/oscillation. if you have any of those problems, stop there and find out why and fix it before moving on with additional hoses/connectors/components/etc.
|
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
What kind of boost control solenoid/boost controller is this? | roninsoldier83 | Factory 2.5L Turbo Powertrain (EJ Series Factory 2.5L Turbo) | 3 | 10-01-2007 10:24 PM |
If the pill is your primary method of birth control, learn from my mistake | George71 | Off-Topic | 59 | 03-15-2005 12:00 PM |
mbc/ebc and peak boost in lower gears? | chrisfranklin | Factory 2.5L Turbo Powertrain (EJ Series Factory 2.5L Turbo) | 2 | 08-02-2004 09:29 PM |
Joe P. MBC XZ Turbo Manual Boost Controller (ebay no reserve) | lstepnio | Private 'For Sale' Classifieds | 0 | 03-22-2004 06:43 PM |
Need Help: An analysis of boost control methods | smiles | Factory 2.0L Turbo Powertrain (EJ Series Factory 2.0L Turbo) | 16 | 01-07-2002 03:12 PM |